Front-Panel Controls
8 Video 3 Inputs: These audio/video inputs& Preset Scan: Press this button to automat-(See pages 22�24 for complete information on
may be used for temporary connection of videoically scan through the stations that have beensetting the output levels.)
games, camcorders, digital still cameras orprogrammed in the AVR 100Os memory. The
ô Surround Off: Press this button to turn off
portable audio products. To select a source tuner will play five seconds of each station
all surround processing and to listen to a pro-
connected to these jacks, press the Vid 3before moving to the next preset station. To
gram in traditional stereo from the left front
Input Selector #.stop the scan when the desired station is heard,
and right front speakers only.
press the button again. (See pages 24�25 for
9 Sleep Button: Press this button to place
more information on the tuner memory system.)
o Mute: Press this button to momentarily
the AVR in the sleep mode. Once the button is
silence the speaker and headphone outputs of
pressed, Information Display 35 will show* Preset Stations Selector: Press this but-
the AVR 100.
the time remaining before the unit will auto-ton to select stations that have been entered
matically go into the standby mode. Tointo the preset memory. (See pages 24�25 for
ö Volume Control: Turn the knob clockwise
decrease the remaining time before the unitmore information on tuner programming.)
to increase volume, counterclockwise to
goes into standby, press the button again, and
decrease the volume. If the AVR is muted,
( Tuner Mode: Press this button to select
each press will decrease the time in the follow-
adjusting volume control will automatically
the stereo or mono mode for FM tuning. In the
ing order.
release the unit from the silenced condition.
STEREO mode a Stereo indicator L will illu-
908070605040
minminminminminminminate in the information display, and stereo
÷ Delay: Press this button to begin the
30201051OFFreception will be provided when stations aresequence of steps required to enter delay time
minminminminmin
transmitting stereo signals. In the MONO mode
settings. (See pages 18�19 for more informa-
) Tape Selector: Press this button to selectthe left and right signals from stereo broadcasts
tion on delay times.)
the device connected to the Tape In jacks hwill be mixed together. Select MONO for better
as the listening source.reception of weak signals.o Digital Input Selector: When playing a
source that has a digital output, press this
! CD: Press this button to select the deviceî Dolby Digital Selector: Press this button to
button to select between the Optical p and
connected to the CD Input jacks ? as the select the Dolby Digital surround mode when lis-
Coaxial o Digital inputs. (See pages 23�24
listening source.tening to a program that carries Dolby Digital
for more information on digital audio.)
information. (See pages 21�24 for more informa-
@ DVD Input Selector: Press this button to
tion on surround modes and digital audio.)u Set Button: When making choices during
select the device connected to the DVD Input
the setup and configuration process, press this
jacks ¤ as the listening and viewing source.i Dolby Pro Logic Selector: Press this
button to enter the desired setting as shown
button to select the Dolby Pro Logic surround
in the Information Display 35,, into the
#Video Input Selectors: Press one of these
mode when listening to an analog program
AVR 100Os memory.
buttons to select a source connected to the rear
that is encoded with surround-sound informa-
panel Video inputs a!, or the front panel
tion. (See page 21�23 for more information onü Channel Trim Button: Press this button
Video 3 input 8.
surround modes.)to trim the output level settings using an nor-
mal input source as the program material. (See
$ 6-Channel Direct Selector: Press this
� Dolby 3 Stereo Selector: Press this but-
page 26 for complete information on triming
button to select the output of an optional,
ton to select the Dolby 3 Stereo listening mode.
the output levels.)
external 6-channel decoder connected to the
This mode is used primarily when a center
6-Ch Direct inputs a as the listening source.
channel speaker but no surround speakers, are33Speaker Select Button: Press this button
installed. (See pages 22 for more informationto begin the process of selecting the speaker
% AM/FM: Press this button to select the
on surround modes.)positions that are used in your listening room.
tuner as the AVR 100Os input source. When it is
(See page 16 for more information on setup
first pressed the last station tuned will be
n Hall Mode Selector: Press this button to
and configuration.)
heard. Press it again to change between AM
activate the Hall 1 mode as an alternative sur-
and FM bands.
round mode when stereo sources are in use.34Selector Buttons: When you are establish-
This mode provides the reverberant atmos-ing the AVR 100Os configuration settings, use
^ Tuning Button: Press the left side of the
phere of a medium-sized concert hall.these buttons to select between the choices avail-
button to tune lower frequency stations and the
able, as shown in the Information Display 35,.
right side of the button to tune higher frequency
o Theater Mode Selector: Press this button
stations. When a station with a strong signal is
to activate the Theater mode as an alternate35 Information Display: This display deliv-
reached, the TUNED indicator N will illumi-
surround mode when stereo sources are in use.ers messages and status indications to help you
nate in the Information Display 35.
operate the receiver. (See page 7 for a complete
ó Test Tone Button: Press this button to
explanation of the Information Display.)
To tune manually, tap the button lightly and
begin the process of setting the AVR 100Os out-
note that the tuner will step up one frequency
put levels. When this button is pressed, a test36 Remote Sensor Window: The sensor
per button press. When the button is held for a
tone will replace the listening source, and circu-behind this window receives infrared signals
few seconds you will note that the unit will
late among the various output channels at afrom the remote control. Aim the remote at this
quickly search the frequency band. Release it
three second interval. The Informationarea and do not block or cover it unless an
once the fast tuning starts and the tuner will
Display 35 will show the location of the chan-external remote sensor is installed.
automatically scan for the next station with an
nel where the test tone noise should be heard.
acceptable signal and then stop.
6 FRONT PANEL CONTROLS |
ACEC
